Amplificatore Modulare professionale 250W, 70/100V. Questa nuova serie di amplificatori finali è stata progettata per soddisfare nel modo più flessibile e professionale le esigenze di un mercato in continua evoluzione. La nuova gamma risponde a precisi criteri operativi ed è costruita e collaudata per garantire all’utente un’affidabilità assoluta, anche nel funzionamento continuo. Grazie all’impiego di un alimentatore switching in tecnologia SMPS (switch mode power supply) e alla realizzazione del 70/100V elettronicamente, senza l’utilizzo del trasformatore di linea, è stato possibile realizzare un prodotto di dimensioni e pesi estremamente contenuti. La serie DM Power è stata concepita per essere installata in cestello rack 19” 3U in grado di accogliere n° 8 moduli affiancati.
PRINCIPALI FUNZIONI:
| Model series “DM.POWER” | DM250 |
| Constant voltage speaker output | 100V – 70V selectable |
| Max Output power RMS @100V | 250W |
| Minimum Load Impedance | 40 Ohm |
| Frequency response | 50Hz ÷ 20KHz ±3db 440Hz ÷ 20KHz ±3db (selectable) |
| S/N Ratio | > 110 dbA (20Hz ÷ 20KHz) |
| Distortion (THD+N) | < 0,05 dbu (1W ÷ Max Power) |
| Input Impedance | 10KΩ |
| Input Sensitivity (mV) | 100÷1000 (Priority Input) – 550 (Line Input) |
| Maximum Input Voltage (V) | 5.50 Vp-p / +8.0 dBu |
| DSP audio processing | 24bit 48Khz, Volume control, Mic Gain control, Soft-VOX, Tone controls |
| AC POWER SUPPLY | |
| Input Voltage (V~) | 230VAc (+10% / -15%) |
| Input Frequency (Hz) | 50 / 60 ± 10% |
| Max Average Input Current | 0,95A (pink noise, max load) |
| DC POWER SUPPLY | |
| Input Voltage (Vdc) 48V.DC nominal. | 42,0 ÷ 55,0 Vdc |
| No-Signal current consumption | 50mA |
| Max Average Input Current | 4,5A (pink noise, max load) |
| INPUT/OUTPUT CONNECTORS | |
| Primary power supply (V~ ) | IEC panel connector |
| Auxiliary power supply (V.-/+ dc) | Polarized panel connector |
| Speaker Output | Terminal block (Euroblock) |
| Signal Input | Terminal block (Euroblock) |
| MIC Input | Polarized panel connector/ RJ45 |
| Std-By | Terminal block (Euroblock) |
| CONTROLS & INDICATORS | |
| Indicators | ON/Std-By, Signal/Clip/Limit, Protect/Temp |
| Controls | Master Volume, HF, LF, 440Hz Cut, Mic Gain, Vox Gain, Std-By |
| PROTECTION | |
| Speaker overload protection | Current limiter |
| Speaker short-circuit protection | Output Disconnection |
| Thermal management | Fan Speed, output signal attenuation, output disconnection |
| DC power protection | Fuse, polarity inversion |
| Mains power protection | Fuse |
| Mains power Spike protection | 480 Joules, 2ms |
| Clipping protection | DSP based amplitude limiter |
| GENERAL DATA | |
| Audible Noise (dB@1mt) | < 40 |
| Operating temperature (°C) | -5 / 40 |
| Relative humidity (%) | < 95 (non-condensing) |
| Dimensions (LxHxP) (mm) | 116 x 53 x 367 |
| Weight (kg) | 2,15 |
Amplificatore Modulare professionale 250W, 70/100V. Questa nuova serie di amplificatori finali è stata progettata per soddisfare nel modo più flessibile e professionale le esigenze di un mercato in continua evoluzione. La nuova gamma risponde a precisi criteri operativi ed è costruita e collaudata per garantire all’utente un’affidabilità assoluta, anche nel funzionamento continuo. Grazie all’impiego di un alimentatore switching in tecnologia SMPS (switch mode power supply) e alla realizzazione del 70/100V elettronicamente, senza l’utilizzo del trasformatore di linea, è stato possibile realizzare un prodotto di dimensioni e pesi estremamente contenuti. La serie DM Power è stata concepita per essere installata in cestello rack 19” 3U in grado di accogliere n° 8 moduli affiancati.
PRINCIPALI FUNZIONI:
| Model series “DM.POWER” | DM250 |
| Constant voltage speaker output | 100V – 70V selectable |
| Max Output power RMS @100V | 250W |
| Minimum Load Impedance | 40 Ohm |
| Frequency response | 50Hz ÷ 20KHz ±3db 440Hz ÷ 20KHz ±3db (selectable) |
| S/N Ratio | > 110 dbA (20Hz ÷ 20KHz) |
| Distortion (THD+N) | < 0,05 dbu (1W ÷ Max Power) |
| Input Impedance | 10KΩ |
| Input Sensitivity (mV) | 100÷1000 (Priority Input) – 550 (Line Input) |
| Maximum Input Voltage (V) | 5.50 Vp-p / +8.0 dBu |
| DSP audio processing | 24bit 48Khz, Volume control, Mic Gain control, Soft-VOX, Tone controls |
| AC POWER SUPPLY | |
| Input Voltage (V~) | 230VAc (+10% / -15%) |
| Input Frequency (Hz) | 50 / 60 ± 10% |
| Max Average Input Current | 0,95A (pink noise, max load) |
| DC POWER SUPPLY | |
| Input Voltage (Vdc) 48V.DC nominal. | 42,0 ÷ 55,0 Vdc |
| No-Signal current consumption | 50mA |
| Max Average Input Current | 4,5A (pink noise, max load) |
| INPUT/OUTPUT CONNECTORS | |
| Primary power supply (V~ ) | IEC panel connector |
| Auxiliary power supply (V.-/+ dc) | Polarized panel connector |
| Speaker Output | Terminal block (Euroblock) |
| Signal Input | Terminal block (Euroblock) |
| MIC Input | Polarized panel connector/ RJ45 |
| Std-By | Terminal block (Euroblock) |
| CONTROLS & INDICATORS | |
| Indicators | ON/Std-By, Signal/Clip/Limit, Protect/Temp |
| Controls | Master Volume, HF, LF, 440Hz Cut, Mic Gain, Vox Gain, Std-By |
| PROTECTION | |
| Speaker overload protection | Current limiter |
| Speaker short-circuit protection | Output Disconnection |
| Thermal management | Fan Speed, output signal attenuation, output disconnection |
| DC power protection | Fuse, polarity inversion |
| Mains power protection | Fuse |
| Mains power Spike protection | 480 Joules, 2ms |
| Clipping protection | DSP based amplitude limiter |
| GENERAL DATA | |
| Audible Noise (dB@1mt) | < 40 |
| Operating temperature (°C) | -5 / 40 |
| Relative humidity (%) | < 95 (non-condensing) |
| Dimensions (LxHxP) (mm) | 116 x 53 x 367 |
| Weight (kg) | 2,15 |
